Code
The sketch ด้านล่างจะอ่านสถานะของ the button อย่างต่อเนื่อง จากนั้นจะเปรียบเทียบสถานะของ the button กับสถานะในครั้งสุดท้ายของมันที่ผ่าน the main loop. หากสถานะของ the button ปัจจุบันแตกต่างจาก the last button state และ the current button state เป็น high จากนั้น the button จะเปลี่ยนจากปิดเป็นเปิด จากนั้น The sketch จะเพิ่ม a button push counter.
The sketch ยังตรวจสอบค่าของ the button push counter อีกด้วยและหากมันเป็นผลคูณของสี่ ไฟ LED บนพิน 13 จะเปิด ถ้าเป็นอย่างอื่นมันก็จะปิด
Learn more
คุณสามารถค้นหาบทช่วยสอนพื้นฐานเพิ่มเติมได้ใน the built-in examples section.
คุณยังสามารถสำรวจ the language reference, ซึ่งเป็นคอลเล็กชันรายละเอียดของ the Arduino programming language.
Last revision 2015/07/28 by SM
The sketch ด้านล่างจะอ่านสถานะของ the button อย่างต่อเนื่อง จากนั้นจะเปรียบเทียบสถานะของ the button กับสถานะในครั้งสุดท้ายของมันที่ผ่าน the main loop. หากสถานะของ the button ปัจจุบันแตกต่างจาก the last button state และ the current button state เป็น high จากนั้น the button จะเปลี่ยนจากปิดเป็นเปิด จากนั้น The sketch จะเพิ่ม a button push counter.
The sketch ยังตรวจสอบค่าของ the button push counter อีกด้วยและหากมันเป็นผลคูณของสี่ ไฟ LED บนพิน 13 จะเปิด ถ้าเป็นอย่างอื่นมันก็จะปิด
Code Select
/*
State change detection (edge detection)
Often, you don't need to know the state of a digital input all the time, but
you just need to know when the input changes from one state to another.
For example, you want to know when a button goes from OFF to ON. This is called
state change detection, or edge detection.
This example shows how to detect when a button or button changes from off to on
and on to off.
The circuit:
- pushbutton attached to pin 2 from +5V
- 10 kilohm resistor attached to pin 2 from ground
- LED attached from pin 13 to ground through 220 ohm resistor (or use the
built-in LED on most Arduino boards)
created 27 Sep 2005
modified 30 Aug 2011
by Tom Igoe
This example code is in the public domain.
https://www.arduino.cc/en/Tutorial/BuiltInExamples/StateChangeDetection
*/
// this constant won't change:
const int buttonPin = 2; // the pin that the pushbutton is attached to
const int ledPin = 13; // the pin that the LED is attached to
// Variables will change:
int buttonPushCounter = 0; // counter for the number of button presses
int buttonState = 0; // current state of the button
int lastButtonState = 0; // previous state of the button
void setup() {
// initialize the button pin as a input:
pinMode(buttonPin, INPUT);
// initialize the LED as an output:
pinMode(ledPin, OUTPUT);
// initialize serial communication:
Serial.begin(9600);
}
void loop() {
// read the pushbutton input pin:
buttonState = digitalRead(buttonPin);
// compare the buttonState to its previous state
if (buttonState != lastButtonState) {
// if the state has changed, increment the counter
if (buttonState == HIGH) {
// if the current state is HIGH then the button went from off to on:
buttonPushCounter++;
Serial.println("on");
Serial.print("number of button pushes: ");
Serial.println(buttonPushCounter);
} else {
// if the current state is LOW then the button went from on to off:
Serial.println("off");
}
// Delay a little bit to avoid bouncing
delay(50);
}
// save the current state as the last state, for next time through the loop
lastButtonState = buttonState;
// turns on the LED every four button pushes by checking the modulo of the
// button push counter. the modulo function gives you the remainder of the
// division of two numbers:
if (buttonPushCounter % 4 == 0) {
digitalWrite(ledPin, HIGH);
} else {
digitalWrite(ledPin, LOW);
}
}
Learn more
คุณสามารถค้นหาบทช่วยสอนพื้นฐานเพิ่มเติมได้ใน the built-in examples section.
คุณยังสามารถสำรวจ the language reference, ซึ่งเป็นคอลเล็กชันรายละเอียดของ the Arduino programming language.
Last revision 2015/07/28 by SM