วิธีการอัพเดท Firmware Jlink V8 ใหม่

Started by Admin, March 29, 2013, 02:26:52 PM

Previous topic - Next topic

Admin

1. Download โปรแกรม AT91-ISP v1.13 มาติดตั้ง http://www.4shared.com/file/V402gwDi/Install_AT91-ISP_v113.html?

2. Download Firmware ตัวใหม่  http://www.4shared.com/rar/7BNw0pCj/jlink-v8.html?

3. เปิดเคสออก หาจุดสำคัญที่ใช้ในการอัพเดท Firmware มีแค่ 2 จุดสำคัญคือ ขา ERASE (pin 55) และ TST (pin 40) => รูปจะตามมาทีหลัง
รับทำ PCB (ออกใบกำกับภาษีได้) => https://www.electoday.com

RoLRoR


pvic

    ขอบคุณครับ

อีกหนึ่งข้อมูล ( เป็นภาษาจีน )  ให้ Google แปลให้ 
http://cn0086.info/%E5%B7%A5%E5%85%B7%E5%88%B6%E4%BD%9C/repaire-j-link

  อีกอันหนึ่ง ผมลองแล้วใช้ได้แล้วตอนนี้
http://blog.chinaunix.net/uid-25977911-id-2159348.html


Admin

1) Install SAM-BA
2) Open J-Link Case
3) Identify ERASE and TST Jumpers
4) Close Jumper "ERASE" and pluggin Jlink to USB port, and wait for > 1 min and remove USB connection
5) Close Jumper "TST" and pluggin Jlink to USB port, and wait for > 1 min and remove USB connection
6) Make sure that ERASE and TST jumpers removed and pluggin Jlink to USB port
7) Now deivce will be identified as Virtual Serial port (USB-Serial adaptor), if fails follow steps 3 to 6 again till you get USB-Serial adaptor in device manager.
8 ) After getting step 7, start SAM-BA and select COM port assigned to Jlink, and board as "AT91SAM7S64-EK" and then click connect,
(Pic 1.jpg)
[img]1.jpg[img]
9) Select .bin file in FLASH tab and click send file (pic2.jpg)
[img]2.jpg[img]
10) You will be prompted with Do you want to unlock involved lock region(s) (0 to 15)? "Yes" to unlock it.,  -> Select YES (pic3.jpg)
[img]3.jpg[img]
11) You will be prompted with Do you want to lock involved lock region(s) (0 to 15)? "Yes" to lock it.,  -> Select NO (pic4.jpg)
[img]4.jpg[img]
12) You are done :-) ..... Happy Coding...
รับทำ PCB (ออกใบกำกับภาษีได้) => https://www.electoday.com

superkai

เอาใหม่ๆ

อันนี้ update ครับ เป็น bin ที่ผมแก้ให้รองรับ software Jlink v476f ครับ

http://www.mediafire.com/download/9kdyh2qfx5o0r85/v8_V4.76f.bin

http://www.mediafire.com/download/bjgjk5bs32blsk0/Setup_JLinkARM_V476f.zip

Erase แล้ว Burn ใหม่ได้เลย แล้วก็ update ตามปกติ ผมใช้คู่กับ Keil MDK-ARM V4.72 ไม่เจอปัญหาครับ