|
- UID
- 7523
- กระทู้
- 7
- เครดิต
- 0
- ผลงาน
- 0
- Money
- 0
- ออนไลน์
- 13 ชั่วโมง
- เข้ามาล่าสุด
- 2010-9-7
|
External Modules for Arduino Boards
แก้ไขล่าสุด megatronics เมื่อ 2010-7-30 17:13
Xbee USB Adapter
Xbee USB adapter is used for the XBee module configuration parameters to facilitate or to use as a wireless data transmission. It can be easily connected to a PC via mini USB cable. Further, it has XBee-setting support software X-CTU. It can also be used as a USB-TTL adapter.
Features :
- Used for the XBee module configuration parameters
- Easily connected to a PC via mini USB cable
- XBee-setting support software X-CTU
- Also used as a USB-TTL adapter
- Voltage: +5V(USB Power)
ราคา 600 บาท
DHT11 Temperature and Humidity Sensor
This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex. Its technology ensures the high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected. This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance advantages.
Each DHT11 sensors features extremely accurate calibration of humidity calibration chamber. The calibration coefficients stored in the OTP program memory, internal sensors detect signals in the process, we should call these calibration coefficients. The single-wire serial interface system is integrated to become quick and easy. Small size, low power, signal transmission distance up to 20 meters, making it a variety of applications and even the most demanding applications. The product is 4-pin single row pin package. Convenient connection, special packages can be provided according to users need.
Specification
Supply Voltage: +5 V
Temperature range :0-50 °C error of ± 2 °C
Humidity :20-90% RH ± 5% RH error
Interface: Digital
ราคา 250 บาท
WiiChuck Adapter (Arduino Compatible)
The WiiChuck Adapter is a small PCB that is designed to be inserted into the connector of a Nintendo Wii Nunchuck to provide access to all 4 wires of the remote. The power, ground and two-wire interface of the Nunchuck are all broken out to a 4-pin 0.1" pitch header. Compared with standard WiiChuck, this WiiChuck has extra 4 pins which allow you connect it to two devices.
The Wii Nunchuck is loaded with features -- a 2-axis joystick, two buttons and a 3 axis ±2g accelerometer -- and any device capable of I2C can communicate with it! The WiiChuck allows you to interface with the Nunchuck without making a mess and cutting the wires.
Specification
Interface Type: I2C
Voltage: +5 V
ราคา 155 บาท
FTDI Basic Breakout 3.3/5V (Arduino Compatible)
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is DTR. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.
There are pros and cons to the FTDI Cable vs the FTDI Basic. This board has TX and RX LEDs that allow you to actually see serial traffic on the LEDs to verify if the board is working, but this board requires a miniB cable. The FTDI Cable is well protected against the elements, but is large and cannot be embedded into a project as easily. The FTDI Basic uses DTR to cause a hardware reset where the FTDI cable uses the RTS signal.
This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro and LilyPad boards use this type of connector.
Specification
3.3/5V output(switchable via Jumpers)
ราคา 450 บาท
Arduino FIO (Arduino Compatible)
This Funnel I/O (Fio) is a board based on the original design of Arduino FIO. It is 100% compatible with original Arduino FIO.
Funnel is a toolkit to sketch your idea physically, and consists of software libraries and hardware. By using Funnel, the user can interface to sensors and/or actuators with various programming languages such as ActionScript 3, Processing, and Ruby.
Arduino Fio is compatible with Funnel. It has connections for a Lithium Polymer battery and includes a charge circuit over USB. An XBee socket is available on the bottom of the board. The Fio has been designed to be wirelessly reprogrammable. Checkout our tutorial on wireless bootloading!
Note: The miniUSB connector is used for battery charging only. To bootload new firmware, you will need an external serial connection over an FTDI Basic, cable, or other serial connection.
Note: The XBee socket and FTDI connection live on the same TX/RX pins of the ATmega328. You will need to remove the XBee module while reprogramming over serial. We recommend using a wireless bootloader whenever possible to avoid this step.
Features
ATmega328V running at 8MHz
Arduino Bootloader
XBee socket
Lithium Polymer battery compatible
MAX1555 LiPo Charger
Reset button
On/Off Switch
Status/Charge/RSSI LEDs
Specification
Size: 28x17x15 mm
Weight: 10 gram
ราคา 640 บาท
Line tracking Sensor for Arduino
This sensor is for line tracking purpose. It detects white and black color, and it outputs via TTL signal.
Specification
Power supply: +5V
Operating current: <10mA
Operating temperature range: 0°C ~ + 50°C
3-wire output interface
Output: TTL(Black for LOW output, White for HIGH output)
ราคา 285 บาท
Triple Axis Accelerometer MMA7260
The MMA7260Q from Freescale is a very nice sensor with easy analog interface. The MMA7260QT is a 3.3V part and outputs an analog voltage for each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). It has selectable sensitivity by dip switch. You will need some extra hardware to convert this analog signal to a usable digital one. The Arduino is really good option for it. This break board is especially designed for Arduino which has 3 JST connector that can be easily plug into our IO/Sensor expansion board.
Specification
Voltage:3.3-8V
Selectable sensitivity:±1．5g／2g／4g／6g
Low power:500μA @ measurement mode，3μA @standby ；
High sensivity: 800 mV／g @ 1.5g；
Low pass filter
Size:23x26mm
Weight: 5 gram
ราคา 475 บาท
Interface Shield for Arduino
This interface shield supports multi-interfaces, SPI interface (directly connected Shiftout module, SPI LCD display module, SPI LED display module), IIC Interface (direct connects IIC lCD display module, IIC transfer IO module), Micro SD card interface (Micro SD card can be directly inserted), SD card storage module interface, TLC full-color LED controller module.
ราคา 450 บาท
URM37 V3.2 Ultrasonic Sensor
This sensor is perfect for any number of applications that require you to perform measurements between moving or stationary objects. Naturally, robotics applications are very popular but you'll also find this product to be useful in security systems or as an infrared replacement if so desired.sensor measures distance using sonar; an ultrasonic (well above human hearing) pulse is transmitted from the unit and distance-to-target is determined by measuring the time required for the echo return.
The URM37 V3.2 Ultrasonic Sensor uses an industrial level AVR processor as the main processing unit. It comes with a temperature sensor which is unique in its class. The sensor has unique three output mode (PWM, RS232 or TTL) which let it easy to adapt to most devices and applications. The sensor provides one channel servo control output which can be used for sweep function.
The URM V3.2 Rev2 has a jumper which allows user to select RS232 level output or TTL level output.
Specification
Power: +5V
Current: <20mA
Working temperature: -10 ~ +70 C
Detecting range: 4cm-3m (3-5m is possible, but depending on situations)
Resolution: 1cm
Interface: PWM, RS232 or TTL (via Jumper)
Servo control: One servo control output
Operating Mode: Serial (PWM) passive control mode; Autonomous Mode; On/OFF Mode
Temperature sensor: 12 bits reading from serial port
Size: 22mm × 51 mm
Weight: 30g
ราคา 645 บาท
Prototyping Shield for Arduino
This is a design for an open-source prototyping shield for Arduino NG/Diecimila. It has tons of cool features, to make prototyping on your Arduino easy. Shipped with fully assembled.
Features
Reset button up top
ICSP header
Lots of GND and +5V rails
DIP prototyping area makes it easy to add more chips
SOIC prototyping area above USB jack for up to 14-pin SOIC chip, narrow medium or wide package.
A 'mini' breadboard included
Extra 6mm button
Compatibility
Arduino NG (Compatible)
Arduino Diecimila (Compatible)
Arduino Duemilanove (Compatible)
ราคา 370 บาท
Screw Shield for Arduino
The Arduino-Compatible Screw Shield is a terminal expansion board that can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use this shield to save yourself from the bad port connection. Feel secure with this arduino-compatible screw shield.
ราคา 280 บาท
360 Degree Rotation Servo
This servo is a double bearing, high torque 360 degree rotation servo. Suitable for mobile robot driven motor.
Specification
Working Voltage: 4.8-7.2V
Working current: 0.1-1.2 A
Torque: 10kg-cm @ 4.8V ; 13kg-cm @6V ; 15kg-cm @7.2V
Average speed: 60 rpm
Rotation range: 0- 360
Working Temperature: 0℃~55℃
Size: 40.2mx 20.2 x 43.2mm
Weight: 52g
ราคา 600 บาท
เงื่อนไขการสั่งซื้อสินค้า
การสั่งซื้อสินค้าให้ PM รายการสินค้าที่ท่านต้องการ แล้วเราจะส่งรายละเอียดการชำระเงินค่าสินค้าและราคาทั้งหมดรวมค่าจัดส่งไปให้
เงื่อนไขการจัดส่งสินค้า
ส่งสินค้าให้ภายใน 24 ชม เมื่อส่งสินค้าเรียบร้อยแล้วจะแจ้งหมายเลข tracking number ให้ทาง PM
สินค้าทุกชิ้นส่งโดย EMS |
ไฟล์แนบ: ด้วยการแบ่งสิทธิ์ของกลุ่มสมาชิก สิทธิ์ของท่านจึงไม่เห็นรูปที่แนบไว้
|
